Skip to content

Chapter 11: Telemetry, Tracking and Command Systems

Key Concepts in This Chapter

  • TT&C system functions: housekeeping telemetry downlink, command uplink, ranging, and Doppler tracking

  • Transponder architecture and coherent ranging principles

  • Ranging systems: pseudo-noise codes, unified S-band, and ranging accuracy

  • Doppler shift measurement for orbit determination

  • Launch and Early Orbit Phase (LEOP) operations and safe mode communications

  • Ground station networks: DSN, commercial networks, and CubeSat amateur systems

  • Command authentication and security for spacecraft telecommand

11.1 Introduction and System Functions

The Telemetry, Tracking and Command (TT&C) system is the communication bridge between a spacecraft and its ground segment. It serves four fundamental functions:

  1. Telemetry (TM): downlink of spacecraft housekeeping data (subsystem status, temperatures, voltages, currents, ADCS measurements) and, in some architectures, payload science data. This allows ground operators to monitor spacecraft health continuously.

  2. Tracking: determination of the spacecraft’s position and velocity through ranging (distance measurement) and Doppler (radial velocity measurement). This data feeds the orbit determination process.

  3. Command (TC): uplink of operator commands from the ground, decoded on-board, and executed by the relevant subsystems. Commands may be immediate or time-tagged for future execution.

  4. Ranging: generation of a precise time-of-flight measurement enabling orbit reconstruction and manoeuvre verification.

The TT&C system operates throughout the entire mission life, from separation detection after launch vehicle separation through nominal operations to end-of-life disposal. It must function reliably even when the spacecraft attitude is unknown (as during LEOP or after a safe mode entry) (Wertz et al. 2011; Pratt et al. 2003; Roddy 2006).

11.2 Frequency Band Selection for TT&C

Table 11.1. ITU frequency allocations for spacecraft TT&C and their characteristics. All frequency values are approximate; exact allocations depend on ITU Radio Regulations and national/regional modifications.
Band Uplink (MHz) Downlink (MHz) Typical Use Key Characteristic
UHF 400–401 435–438 LEO beacons, CubeSats Omni-directional, robust
S-band 2025–2110 2200–2290 LEO/GEO TT&C, LEOP Workhorse TT&C band
X-band TC 7190–7235 — Deep space uplink High gain needed
X-band TM — 8025–8500 EO data downlink, deep space TM High bandwidth
Ka-band 27.0–27.5 GHz 25.5–27.0 GHz High-rate TT&C, intersat Rain attenuation impact

S-band (\(2\)–\(4\,\mathrm{GHz}\)) is the most widely used TT&C band for LEO and GEO missions. It offers a good balance between:

  • Antenna size: a \(\lambda/4\) monopole at \(2.2\,\mathrm{GHz}\) is \(34\,\mathrm{mm}\) long, small enough for omnidirectional coverage.

  • Atmospheric losses: rain and cloud attenuation at S-band is \(<0.5\,\mathrm{dB}\) for \(99.9\%\) of the year at most locations.

  • Transponder maturity: S-band transponders with heritage going back to Sputnik are available from multiple vendors.

For deep space missions beyond \(3\times10^6\,\mathrm{km}\), X-band is preferred for its higher antenna gain at manageable antenna sizes (\(3\)–\(5\,\mathrm{m}\) HGA provides 45–50 dBi at X-band).

11.3 Transponder Architecture

The spacecraft transponder implements both the uplink receiver and downlink transmitter in a single unit, with the critical coherent turnaround function for ranging. The block diagram consists of:

Uplink receiver chain:

  1. Low-Noise Amplifier (LNA): amplifies the received RF signal with minimum noise figure (\(NF = 0.5\)–\(2\,\mathrm{dB}\))

  2. Bandpass filter: rejects out-of-band interference

  3. Downconverter: mixes RF carrier to intermediate frequency (IF) using a local oscillator referenced to the on-board frequency reference

  4. IF amplifier and automatic gain control (AGC)

  5. Demodulator: extracts the baseband data (PCM/PSK subcarrier demodulation)

  6. Decoder: CCSDS TC Space Data Link Protocol frame synchronisation and CLTU decoding

  7. Command decoder: parses decoded frame into individual telecommands for distribution

Coherent turnaround (ranging): The transponder generates a phase-coherent downlink carrier by multiplying the received uplink carrier frequency by a fixed rational number (the turnaround ratio \(k\)):

\[f_{\mathrm{DL}} = k \cdot f_{\mathrm{UL}}\tag{11.1}\]

For S-band, the standard turnaround ratio is \(k = 240/221\) (uplink \(\approx 2.1\,\mathrm{GHz}\), downlink \(\approx 2.3\,\mathrm{GHz}\)). For deep-space X-band, \(k = 880/749\). This coherent relationship allows the ranging tone or PN code applied on the uplink to be retrieved on the downlink with a precisely known and constant delay.

Downlink transmitter chain:

  1. Frequency synthesiser: generates downlink RF carrier coherent with uplink

  2. BPSK/QPSK modulator: modulates TM data onto the carrier

  3. Driver amplifier

  4. Solid State Power Amplifier (SSPA) or TWTA: final power amplification (\(1\)–\(20\,\mathrm{W}\) typical for TT&C)

  5. Bandpass filter (harmonic rejection)

  6. Switch to antenna selection (main/redundant)

Figure 11.1. Coherent S-band TT&C transponder block diagram. The phase-locked loop (PLL) coherently regenerates the downlink carrier from the uplink, enabling two-way Doppler and ranging measurements. The ranging tone or PN code passes transparently through the transponder.

11.4 Ranging Systems

11.4.1 Two-Way Ranging Principle

Two-way ranging measures the round-trip light time (RTLT) from which the spacecraft range is derived:

\[\rho = \frac{c \cdot \mathrm{RTLT}}{2}\tag{11.2}\]

The process consists of:

  1. Ground station transmits a ranging signal (tone or PN code) modulated onto the uplink carrier.

  2. Transponder coherently retransmits the ranging signal on the downlink with the known turnaround delay.

  3. Ground station correlates the received downlink ranging signal with the transmitted reference, measuring RTLT.

  4. Range computed: \(\rho = c \cdot \mathrm{RTLT}/2\), correcting for the transponder’s internal turnaround delay (typically measured pre-launch).

Corrections applied to the raw ranging measurement include:

  • Ionospheric delay: \(\Delta\rho_{\mathrm{iono}} \propto \mathrm{TEC}/f^2\) (significant at S-band, \(\sim 1\)–\(10\,\mathrm{m}\))

  • Tropospheric delay: \(\Delta\rho_{\mathrm{tropo}} \approx 2.3\,\mathrm{m}\) (zenith, dry component) + water vapour term

  • Relativistic corrections: Sagnac effect, gravitational frequency shift

The one-sigma ranging accuracy achievable is:

\[\sigma_\rho = \frac{c}{2 \cdot 2\pi \cdot f_{\mathrm{range}} \cdot \sqrt{2 P_{\mathrm{range}} T / N_0}}\tag{11.3}\]

For a tone ranging system with a \(f_{\mathrm{range}} = 1\,\mathrm{MHz}\) highest-frequency tone and \(P/N_0 = 50\,\mathrm{dB\text{-}Hz}\), accuracy of \(\sigma_\rho \approx 1\)–\(5\,\mathrm{m}\) is achievable.

11.4.2 Pseudo-Noise Ranging

CCSDS-standardised PN ranging (CCSDS 414.1-B-2) uses a binary pseudo-random sequence modulated onto the uplink. The PN code has two critical properties:

  • Autocorrelation: the code’s autocorrelation function (ACF) has a sharp peak at zero delay and low sidelobes, enabling precise timing.

  • Unambiguous range: the code period \(T_{\mathrm{code}}\) must be longer than the round-trip light time to the target, avoiding range ambiguity.

CCSDS defines two code classes:

  • Class A (Rosette code, component code length \(N_c = 2\)): recommended for near-Earth missions (\(\leq 10^6\,\mathrm{km}\)). Unambiguous range: \(\sim 2 \times 10^6\,\mathrm{km}\).

  • Class B (T4B code): for deep space (\(> 10^6\,\mathrm{km}\)). Unambiguous range: \(\sim 10^9\,\mathrm{km}\).

11.4.3 Unified S-Band System

The Unified S-Band (USB) system, originally developed for the Apollo programme, combines TM, TC, and ranging on a single S-band carrier. Telemetry is modulated as a PCM/PM subcarrier (\(f_{\mathrm{sc}} = 1.024\) MHz for wideband TM), command is modulated as a separate subcarrier, and ranging tones are injected simultaneously. The coherent transponder turnaround preserves the phase relationships of all three modulation components.

11.5 Doppler Tracking and Orbit Determination

When the spacecraft has a radial velocity component \(v_r\) relative to the ground station, the received frequency is Doppler-shifted. For the two-way case (ground transmits \(f_0\), spacecraft returns coherently at \(k \cdot f_0\), ground receives \(f_r\)):

\[f_r \approx k \cdot f_0 \cdot \frac{1 + 2 v_r / c}{1} \approx k \cdot f_0 \left(1 + \frac{2 v_r}{c} \right)\tag{11.4}\]

The two-way Doppler shift is therefore:

\[\Delta f = f_r - k \cdot f_0 = \frac{2 k f_0 v_r}{c}\tag{11.5}\]

The radial velocity is recovered as:

\[v_r = \frac{c \Delta f}{2 k f_0}\tag{11.6}\]

For a LEO spacecraft at \(v_{\mathrm{orbital}} = 7.6\,\mathrm{km/s}\) and \(k = 240/221 \approx 1.086\), the peak two-way Doppler shift at S-band (\(f_0 = 2.1\,\mathrm{GHz}\) uplink) is:

\[\Delta f_{\max} = \frac{2 \times 1.086 \times 2.1\times10^9 \times 7600}{3\times10^8} \approx 116\,\mathrm{kHz}\tag{11.7}\]

Ground-based orbit determination uses a least-squares batch estimator or Kalman filter to fit a dynamical model to tracking data (range \(+\) Doppler from multiple ground stations). The orbit solution improves as tracking arc length increases. A 3-station pass set covering \(> 30^{\circ}\) of orbital arc typically achieves position accuracy of \(10\)–\(50\,\mathrm{m}\) for LEO (RSS), dominated by atmospheric delay uncertainties.

The TT&C link budget evaluates whether the signal-to-noise ratio at the receiver is adequate for reliable demodulation. The fundamental link budget equation in decibels is:

\[E_b/N_0 = P_T + G_T - L_{\mathrm{space}} - L_{\mathrm{atm}} + G_R - k_B - R_{\mathrm{bit}}\tag{11.8}\]

where:

  • \(P_T\) = transmit power (dBW)

  • \(G_T\) = transmit antenna gain (dBi)

  • \(L_{\mathrm{space}} = 20\log_{10}(4\pi d/\lambda)\) = free-space path loss (dB)

  • \(L_{\mathrm{atm}}\) = atmospheric losses (dB, rain + gas absorption)

  • \(G_R\) = receive antenna gain (dBi)

  • \(k_B = -228.6\,\mathrm{dBW/K/Hz}\) = Boltzmann constant in dB

  • \(R_{\mathrm{bit}}\) = data rate (dBbps)

  • \(N_{\mathrm{sys}}\) = system noise temperature (dBK, \(T_{\mathrm{sys}} = T_{\mathrm{ant}} + T_{\mathrm{LNA}} + T_{\mathrm{feed}} + …\))

The generous link margin of \(21\,\mathrm{dB}\) shown in Table 11.2 confirms the TT&C link is robust. In practice, TT&C links are designed with \(>6\,\mathrm{dB}\) margin at worst-case geometry (lowest elevation angle) to accommodate unpredicted losses, attitude errors, and antenna pattern nulls.

11.7 TT&C Antennas

11.7.1 Omnidirectional and Low-Gain Antennas

Full spherical coverage is required for LEOP and safe mode, where the spacecraft attitude is undefined or in the process of being established. Omnidirectional coverage is achieved with:

  • Monopole/dipole: half-wave dipole gives \(G = 2.15\,\mathrm{dBi}\) with toroidal pattern, nulls along the axis. Two orthogonal dipoles cover the full sphere.

  • Cavity-backed slot: flush-mounted in the spacecraft panel, \(G = 3\)–\(5\,\mathrm{dBi}\), hemispherical coverage per unit.

  • Patch antenna: low-profile, \(G = 6\)–\(8\,\mathrm{dBi}\) over a \(\pm60^{\circ}\) half-angle cone, commonly used in pairs on opposite faces for full coverage.

  • Horn antenna: for downlink TM on GEO (\(G = 15\)–\(20\,\mathrm{dBi}\), covering the full Earth disk from GEO requires \(\theta_{3\mathrm{dB}} \approx 18^{\circ}\)).

For deep space missions (MRO, Voyager, New Horizons), a High-Gain Antenna (HGA) with \(G = 42\)–\(47\,\mathrm{dBi}\) is required to overcome path losses at AU-scale distances, supplemented by a Low-Gain Antenna (LGA) for near-Earth contingency operations.

11.8 Launch and Early Orbit Phase Operations

11.8.1 LEOP Timeline

LEOP represents the most critical operational period of the mission. The typical LEO LEOP sequence proceeds as:

  1. T = 0: Separation: pyrotechnic separation nuts release, springs separate spacecraft from upper stage. Separation switch triggers on-board autonomous sequence.

  2. T = \(+5\) s: On-board software starts. Beacon transmission begins autonomously on TT&C transmitter (omnidirectional antenna, \(1\,\mathrm{kbps}\), no encryption).

  3. T = \(+5\) to \(+20\) min: First ground station contact (typically a station under the launch orbit track). Ground acquires beacon, establishes TM/TC link.

  4. T = \(+20\) min: First TM packet received. Spacecraft health check performed: battery SoC, temperature, attitude mode.

  5. T = \(+30\) to \(+60\) min: Solar array deployment commanded. Current increase on solar array output confirms deployment.

  6. T = \(+1\) to \(+4\) h: Attitude initialisation: magnetometer-based coarse Sun acquisition, followed by Sun sensor-based fine Sun pointing. Power positive confirmed.

  7. T = \(+4\) to \(+24\) h: Orbit determination with tracking data from multiple stations. Manoeuvre planning for orbit correction if needed.

  8. T = \(+24\) to \(+72\) h: In-orbit check-out (IOCO) begins. Subsystem activation and verification sequence. Payload switch-on (if no outgassing/thermal conditioning required).

  9. T = \(+3\) to \(+30\) days: Commissioning phase. End-to-end performance verification, calibration, transition to nominal operations.

Figure 11.2. Typical LEOP timeline for a LEO satellite. Ground station contact windows (shaded bars) provide telecommand opportunities. The first 24 h are the most critical, requiring 24/7 ground staffing and contingency command sequences prepared for each anomaly scenario.

11.8.2 Safe Mode

Safe Mode (also called Survival Mode or Emergency Mode) is an autonomous spacecraft configuration entered when a critical anomaly is detected that the on-board FDIR cannot resolve at a lower level. From a TT&C perspective, safe mode operation requires:

  • Transmission on omnidirectional antenna (not directional HGA) to ensure contact regardless of attitude

  • Reduced, robust downlink rate (\(\leq 4\,\mathrm{kbps}\) BPSK) with forward error correction to maximise link margin

  • Periodic beacon transmission even without ground command, to enable ground station acquisition without prior knowledge of spacecraft state

  • Automatic uplink search: transponder scans across uplink frequency uncertainties if frequency drift has occurred

  • Minimum housekeeping telemetry downlink (power, temperature, attitude error, FDIR event log)

11.9 Telecommand Management

Commands are uplinked as a CCSDS TC Transfer Frame encapsulated in a Communications Link Transmission Unit (CLTU). The CLTU encoding provides robust error detection:

\[\mathrm{CLTU} = \underbrace{10101010…10101011}_{\text{Start Sequence (16 bits)}} \; \underbrace{(\mathrm{TC\,frame} + \mathrm{EDAC})}_{\text{$n$ code blocks of 64 bits}} \; \underbrace{C8… FEh}_{\text{Tail Sequence (8 octets)}}\tag{11.9}\]

Each 64-bit code block consists of 56 data bits and an 8-bit BCH code providing single-error correction and double-error detection within the block. A command rejected by the on-board decoder (due to CLTU decode error, authentication failure, or address mismatch) generates a Command Reject Acceptance Report downlinked as a TM packet.

11.9.2 Command Priority and Sequencing

Commands are classified by priority:

  1. Critical commands: one-time commands with irreversible effects (pyrotechnic firing, antenna deployment, mode change to safe mode). These require additional safeguards: separate arm/fire sequence, time window, count check.

  2. Operational commands: routine operational commands (payload power, attitude mode, downlink rate). Executed immediately or at specified time-tag.

  3. Low-priority commands: parameter updates, table uploads, maintenance commands. May be queued and executed during ground contact.

Time-tagged commands (TTC) are stored on-board in a command timeline with absolute on-board time tags. The on-board time correlation with UTC is maintained via periodic time correlation messages uplinked during ground contact.

11.10 Command Authentication and Security

The threat of unauthorised command injection (spoofing) is a serious concern, particularly for high-value missions. CCSDS Space Data Link Security (SDLS, CCSDS 355.0-B-1) defines a security protocol for authenticating and/or encrypting TC frames at the Space Data Link layer.

The standard supports two security services:

  1. Authentication Only: a Message Authentication Code (MAC) is appended to each TC frame. The ground computes the MAC using AES-256 CMAC with the current session key; the spacecraft verifies it before executing commands.

  2. Encryption + Authentication: TC frame payload is AES-256 encrypted and MACed. Protects against both spoofing and interception of sensitive command content.

The MAC computation for a TC frame of \(n\) octets using AES-CMAC is:

\[\mathrm{MAC} = \mathrm{AES\text{-}CMAC}(K_{\mathrm{session}}, \mathrm{TC\,Frame}[0:n-1])\tag{11.10}\]

Replay attack prevention is achieved by including a monotonically increasing frame sequence number in the authenticated portion; the spacecraft rejects frames whose sequence number is not greater than the last accepted frame.

Key management requires periodic key rotation. New session keys are uplinked encrypted under a long-term Key Encryption Key (KEK) pre-loaded at launch.

11.11 Deep Space Network

The NASA/JPL Deep Space Network (DSN) operates three ground station complexes at approximately \(120^{\circ}\) longitude separation to provide continuous Earth rotation coverage:

  • Goldstone (GDSCC), California, USA (\(116.8^{\circ}\) W)

  • Madrid (MDSCC), Spain (\(4.2^{\circ}\) W)

  • Canberra (CDSCC), Australia (\(148.9^{\circ}\) E)

Each complex operates multiple antenna apertures:

  • \(70\,\mathrm{m}\) antenna (DSS-14, DSS-63, DSS-43): gain \(\sim74\,\mathrm{dBi}\) at X-band, \(G/T \approx 60\,\mathrm{dB/K}\). Reserved for critical deep space operations.

  • \(34\,\mathrm{m}\) BWG (Beam Waveguide) antennas: gain \(\sim68\,\mathrm{dBi}\) at X-band. Used for routine mission support.

  • \(34\,\mathrm{m}\) HEF (High Efficiency) antennas.

Table 11.3. DSN performance summary for X-band operations (typical values, current capability).
Parameter 70 m 34 m BWG Unit
Receive frequency 8.4 8.4 GHz
Receive gain 74.5 68.0 dBi
System noise temperature (\(T_{\mathrm{sys}}\)) 25 20 K
\(G/T\) 60.5 55.0 dB/K
Transmit frequency 7.2 7.2 GHz
Transmit power (typical X-band) 20 20 kW
EIRP (approx.) \(\sim 115\) \(\sim 110\) dBW
Supported data rates mission- and distance-dependent

At interplanetary distances, the free-space path loss is enormous. For Voyager 1 at a distance of roughly \(165\,\mathrm{AU}\) (as of 2025), transmitting \(20\,\mathrm{W}\) at X-band with a \(3.7\,\mathrm{m}\) HGA (\(\sim 48\,\mathrm{dBi}\)), the free-space path loss is about \(319\,\mathrm{dB}\) and the received signal power at a DSN 70 m antenna is approximately \(-184\,\mathrm{dBW}\) (\(\sim 4\times10^{-19}\,\mathrm{W}\)), requiring the full sensitivity of the DSN receiver and error-correcting coding to achieve a data rate of \(\sim 160\,\mathrm{bps}\).

11.12 Commercial Ground Station Networks

The emergence of commercial ground-as-a-service (GaaS) offerings has transformed TT&C operations for commercial and small satellite operators:

  • AWS Ground Station (Amazon): network of ground stations operated by Amazon, accessible via API with pay-per-use pricing. Supports S-band and X-band. Data delivered directly to AWS cloud for processing.

  • Microsoft Azure Orbital: similar service by Microsoft, integrated with Azure cloud.

  • KSAT (Kongsberg Satellite Services): the world’s largest commercial ground station network, with \(>200\) antennas at \(>24\) sites including polar stations (Svalbard, Troll) providing \(>10\) contacts/day for polar LEO orbits.

  • SSC Universal Space Network (USN): \(11\) stations worldwide.

  • Leaf Space: \(8\) stations, focused on small satellites and NewSpace.

The economics of commercial ground stations have enabled small satellite operators to avoid the capital expenditure of building their own ground infrastructure (\(>\)EUR 1M per station), instead paying per-contact fees of EUR 50–500.

11.13 TT&C for CubeSats

CubeSats typically use UHF (437–438 MHz) for TT&C, leveraging:

  • Small antennas: a \(\lambda/4\) monopole at 437 MHz is \(17\,\mathrm{cm}\) long. Deployable monopoles or dipoles provide \(\sim 0\,\mathrm{dBi}\) gain.

  • Amateur satellite band: the IARU-coordinated 435–438 MHz band is allocated to Amateur Satellites, accessible to university and research missions.

  • AX.25 protocol: the packet radio protocol used by AMSAT and the amateur radio community since the 1980s, providing a simple data link layer with CRC error detection.

  • Amateur radio support: the international AMSAT network of volunteer stations can support telemetry reception, even without a dedicated mission ground station.

  • Link performance: at 437 MHz, 0.5 W transmit power (\(+27\,\mathrm{dBm}\)) from a CubeSat dipole antenna with a \(3\,\mathrm{m}\) yagi ground antenna (\(G = 14\,\mathrm{dBi}\)) at 600 km altitude gives \(C/N_0 \approx 65\,\mathrm{dBHz}\), sufficient for \(\leq 9600\,\mathrm{bps}\) AX.25 (AFSK or GMSK).

Modern CubeSat missions increasingly use S-band for primary downlink (up to \(40\,\mathrm{Mbps}\)) and retain UHF only as a backup TT&C channel.

11.14 Future Directions: Optical TT&C

Optical (laser) communications offer orders-of-magnitude improvement in bandwidth relative to RF at similar power and aperture size. NASA’s Laser Communications Relay Demonstration (LCRD), launched December 2021, demonstrates two-way optical communications at \(1.2\,\mathrm{Gbps}\) downlink via geosynchronous relay. The Lunar Laser Communication Demonstration (LLCD) achieved \(622\,\mathrm{Mbps}\) downlink from lunar orbit.

The optical link budget uses the same fundamental equation as RF but expressed differently:

\[P_R = P_T \cdot G_T \cdot L_{\mathrm{FSL}} \cdot G_R = P_T \cdot \left(\frac{\pi D_T}{\lambda \theta_D}\right)^2 \cdot \left(\frac{\lambda}{4\pi d}\right)^2 \cdot \left(\frac{\pi D_R^2}{4}\right) / A_r\tag{11.11}\]

where \(D_T\) is the transmit telescope diameter, \(\theta_D = 2.44 \lambda/D_T\) is the diffraction-limited beam divergence, \(D_R\) is the receive telescope diameter, and \(d\) is the range.

The primary challenge for optical TT&C is cloud blockage and atmospheric turbulence. Mitigation strategies include site diversity (multiple geographically separated ground receivers), adaptive optics (wavefront correction to compensate atmospheric distortion), and relay via GEO optical satellites above the cloud layer.

11.15 Summary

The TT&C subsystem is the indispensable communication thread between the spacecraft and the ground segment that must never be broken. Its design must prioritise robustness and coverage over performance, particularly during LEOP and safe mode operations. The fundamental physical constraints—free-space path loss, atmospheric effects, and antenna pattern coverage—drive the key design decisions of frequency band, power level, and antenna selection.

The revolution in commercial ground station services and the increasing adoption of standardised CCSDS protocols are dramatically reducing the cost and complexity of TT&C operations for new entrants to the space sector. Looking forward, the transition to optical communications will enable data rates measured in gigabits per second, fundamentally changing the balance between on-board storage and real-time downlink for science missions (Pratt et al. 2003; Roddy 2006).

Further Reading

  • Pratt, T., Bostian, C., Allnutt, J.: Satellite Communications, 2nd edn., Wiley (2003).

  • Roddy, D.: Satellite Communications, 4th edn., McGraw-Hill (2006).

  • CCSDS: Pseudo-Noise (PN) Ranging Systems, CCSDS 414.1-B-2, Washington DC (2014).

  • CCSDS: Space Data Link Security (SDLS) Protocol, CCSDS 355.0-B-1 (2015).

  • Wertz, J. R., Everett, D. F., Puschell, J. J.: Space Mission Engineering: The New SMAD, Microcosm Press (2011).