Skip to content

Link Budget Templates and Worked Examples

“A link budget that closes in analysis often does not close in practice, and one that closes in practice is always the result of careful attention to every term.”
—Spacecraft systems engineering maxim

Link budget analysis is the accounting exercise that determines whether a radio or optical communication link will deliver adequate signal quality to support the required data rate under defined propagation conditions. Every communications satellite, every TT&C system, and every ground station design begins with a link budget. This appendix provides a systematic treatment of the methodology, complete worked examples for four representative link types encountered in satellite engineering, a summary of key formulae, and annotated templates suitable for adaptation to new designs.

Introduction to Link Budget Analysis

The received carrier-to-noise density ratio \(C/N_0\) (in dBHz) is the central quantity of any link budget. It expresses the ratio of received carrier power to the noise power per unit bandwidth, and is the quantity that determines how much information can be recovered from the received signal before any bandwidth-limiting process is applied. The fundamental link equation in logarithmic form is:

\[\begin{align*} \frac{C}{N_0}\bigg|_{\text{dBHz}} &= \text{EIRP}_{\text{dBW}} - \text{FSPL}_{\text{dB}} - L_{\text{atm,dB}} - L_{\text{misc,dB}} + \left(\frac{G}{T}\right)_{\text{dB/K}} - k_B \end{align*}\]

where:

  • \(\text{EIRP} = P_t + G_t - L_{\text{tx}}\) (dBW): Effective Isotropic Radiated Power, the transmit power augmented by antenna gain and reduced by transmit path losses

  • \(\text{FSPL} = 20\log_{10}\!\left(\frac{4\pi d}{\lambda}\right)\) (dB): Free-Space Path Loss, the geometric spreading loss over slant range \(d\) at wavelength \(\lambda\)

  • \(L_{\text{atm}}\) (dB): Atmospheric absorption including gaseous (O\(_2\), H\(_2\)O), cloud, and rain losses

  • \(L_{\text{misc}}\) (dB): Miscellaneous losses including polarisation mismatch, pointing error, Faraday rotation, and implementation loss

  • \(G/T\) (dB/K): Receive system figure of merit, the receive antenna gain divided by system noise temperature

  • \(k_B = -228.6\) dBW/K/Hz: Boltzmann’s constant in logarithmic form

System Noise Temperature

The receive system noise temperature \(T_{\text{sys}}\) is the sum of all noise contributions referred to the antenna output port:

\[\begin{align*} T_{\text{sys}} &= T_{\text{ant}} + T_{\text{feed}} + \frac{T_{\text{LNA}}}{G_{\text{ant}}} + \frac{T_{\text{backend}}}{G_{\text{ant}} G_{\text{LNA}}} \end{align*}\]

In practice, for high-gain antennas where \(G_{\text{ant}} \gg 1\), the system noise temperature is dominated by the antenna noise temperature \(T_{\text{ant}}\) (which includes both sky noise and ground pickup through sidelobes) and the LNA noise temperature \(T_{\text{LNA}}\). For a receive system with an antenna noise temperature of 30 K (pointing at cold sky), a feed loss of 0.3 dB (equivalent to 20 K), and an LNA with 1 dB noise figure (75 K), the system noise temperature is approximately:

\[\begin{align*} T_{\text{sys}} &\approx 30 + 20 + 75 = 125~\text{K} \end{align*}\]

The link margin \(M\) is the difference between the received \(C/N_0\) and the minimum required \(C/N_0\) needed to close the link at the specified modulation and coding with the required bit error rate (BER):

\[\begin{align*} M &= \left(\frac{C}{N_0}\right)_{\text{received}} - \left(\frac{C}{N_0}\right)_{\text{required}} \end{align*}\]

A positive margin indicates the link closes; a negative margin indicates link failure. Design convention typically requires a minimum margin of 3 dB for geostationary links in clear sky, with additional margins for rain fade specified at an exceedance probability (e.g., 5 dB rain fade margin for 99.9% annual availability at mid-latitudes for Ka-band). The relationship between bit error rate and \(E_b/N_0\) (energy-per-bit to noise density ratio) is:

\[\begin{align*} \frac{E_b}{N_0}\bigg|_{\text{dB}} &= \frac{C}{N_0}\bigg|_{\text{dBHz}} - 10\log_{10}(R_b) \end{align*}\]

where \(R_b\) is the information bit rate in bit/s.

Shannon Capacity Bound

The Shannon–Hartley theorem provides the theoretical maximum channel capacity \(C\) (bit/s) as a function of bandwidth \(B\) (Hz) and signal-to-noise ratio SNR:

\[\begin{align*} C &= B \log_2\!\left(1 + \text{SNR}\right) \end{align*}\]

where \(\text{SNR} = C/N = (C/N_0)/B\). Modern forward error correction codes (turbo codes, LDPC) operate within about 0.5–1.0 dB of the Shannon limit. The spectral efficiency \(\eta_s = C/B = \log_2(1 + \text{SNR})\) in bit/s/Hz determines the maximum data rate achievable within a given bandwidth allocation.

Example 1: Ka-band GEO Downlink

Scenario Definition

This example computes the link budget for a Ka-band downlink from a geostationary communications satellite to a small VSAT terminal. All inputs are assumed, illustrative values and not the parameters of a specific system.

Scenario: GEO satellite at 35,786 km altitude (slant range taken as 36,000 km), 20 GHz downlink frequency, 10 W transmit power, a shaped-beam spacecraft antenna with a gain of 35 dBi, and a 0.9 m ground dish; the link is evaluated for a rain fade margin appropriate to a temperate climate.

Link Budget Calculation

The free-space path loss at 20 GHz (wavelength \(\lambda = c/f = 3\times10^8/20\times10^9 = 0.015\) m) over 36,000 km is:

\[\begin{align*} \text{FSPL} &= 20\log_{10}\!\left(\frac{4\pi \times 36{,}000 \times 10^3}{0.015}\right) = 20\log_{10}(3.02 \times 10^{10}) = 209.6~\text{dB} \end{align*}\]

The receive antenna gain for a 0.9 m dish at 20 GHz with 60% efficiency is:

\[\begin{align*} G_r &= 0.60 \times \left(\frac{\pi \times 0.9 \times 20 \times 10^9}{3 \times 10^8}\right)^2 = 0.60 \times 35{,}531 = 21{,}319 \Rightarrow 43.3~\text{dBi} \end{align*}\]

A pointing and off-axis allowance of 3.8 dB (a conservative allowance for operation at the edge of the satellite coverage) reduces this to an effective \(G_r = 39.5\) dBi.

Table 1. Ka-band GEO Downlink Budget (20 GHz, GEO at 35,786 km)
Parameter Value Units
Transmit Side
Transmit power \(P_t\) \(+10.0\) dBW (\(= 10\) W)
Transmit antenna gain \(G_t\) \(+35.0\) dBi (shaped beam, assumed)
Waveguide and feed losses \(L_{\text{tx}}\) \(-1.0\) dB
EIRP \(\mathbf{+44.0}\) dBW
Propagation
Free-space path loss FSPL \(-209.6\) dB (\(d=36{,}000\) km, \(f=20\) GHz)
Atmospheric absorption \(L_{\text{gas}}\) \(-0.5\) dB (O\(_2\), H\(_2\)O at 45\(^\circ\) el.)
Rain fade margin (0.01% time) \(-5.0\) dB (illustrative, temperate climate)
Polarisation mismatch / pointing \(-0.5\) dB
Total path losses \(\mathbf{-215.6}\) dB
Receive Side
Receive antenna gain \(G_r\) \(+39.5\) dBi (0.9 m dish, 60% efficiency, incl. allowance)
System noise temperature \(T_{\text{sys}}\) 150 K \(= +21.8\) dBK
Receive figure of merit \(G/T\) \(+17.7\) dB/K (\(= 39.5 - 21.8\))
Boltzmann constant \(k_B\) \(+228.6\) dBW/K/Hz
Link Performance
Received \(C/N_0 = 44.0 - 215.6 + 17.7 + 228.6\) \(\mathbf{+74.7}\) dBHz
Required \(C/N_0\) for DVB-S2
Modulation: QPSK, code rate 3/4
Required \(E_b/N_0\) (quasi-error-free, from \(E_s/N_0 = 4.03\) dB) \(+2.3\) dB
Modem implementation loss \(+1.0\) dB
Data rate \(R_b = 8\) Mbps: \(10\log_{10}(8\times10^6)\) \(+69.0\) dBHz
Required \(C/N_0 = 2.3 + 1.0 + 69.0\) \(\mathbf{+72.3}\) dBHz
Link margin \(= 74.7 - 72.3\) \(\mathbf{+2.4}\) dB

Interpretation

The link closes with a positive but thin margin of 2.4 dB even with the 5.0 dB rain fade margin already included. In clear sky the margin is 7.4 dB (2.4 dB plus the 5.0 dB allocated to rain), which an adaptive coding and modulation scheme can convert into a higher data rate, as described in the note below. Margins of this size are typical of a system designed to run close to its limits to maximise capacity; a design without ACM would normally carry more fade margin or a lower data rate.

DVB-S2 Adaptive Coding and Modulation (ACM). Modern Ka-band broadband systems use ACM: when the link margin is high (clear sky), the modem switches to a higher spectral efficiency MODCOD (for example 16APSK 3/4); when rain reduces the margin, it falls back to a more robust MODCOD (for example QPSK 1/2). This turns the rain margin from a fixed loss into a variable throughput gain.

Example 2: S-band TT&C Uplink

Scenario Definition

This example computes the command uplink from a ground station to a LEO spacecraft. The scenario represents typical mission operations for a small satellite, where the ground station must reliably command the spacecraft even at the lowest usable elevation angle. All inputs are assumed, illustrative values.

Scenario: 2.1 GHz S-band command uplink, 5 W transmitter at the ground station with a 3 m dish, LEO satellite at 600 km circular orbit, worst-case elevation angle 10\(^\circ\) (slant range \(\approx 1930\) km), omnidirectional spacecraft receive antenna, 4 kbps BPSK command link.

Link Budget Calculation

At 2.1 GHz, wavelength \(\lambda = 3\times10^8 / 2.1\times10^9 = 0.143\) m. For the worst-case 10\(^\circ\) elevation geometry, the slant range from a 600 km circular orbit is:

\[\begin{align*} d_{\text{slant}} &= \sqrt{(R_E + h)^2 - R_E^2\cos^2(\varepsilon)} - R_E\sin(\varepsilon) \approx 1930~\text{km at } \varepsilon=10^\circ \end{align*}\]

The free-space path loss at worst-case range is:

\[\begin{align*} \text{FSPL} &= 20\log_{10}\!\left(\frac{4\pi \times 1{,}930 \times 10^3}{0.143}\right) = 20\log_{10}(1.70 \times 10^{8}) = 164.6~\text{dB} \end{align*}\]

The ground antenna gain for a 3 m dish at 2.1 GHz with 55% efficiency is \(0.55\,(\pi \times 3 \times 2.1\times10^9/3\times10^8)^2 = 2{,}394 \Rightarrow 33.8\) dBi. For BPSK at BER \(= 10^{-5}\), the required \(E_b/N_0 = 9.6\) dB. At \(R_b = 4000\) bps:

\[\begin{align*} \left(\frac{C}{N_0}\right)_{\text{req}} &= \frac{E_b}{N_0} + 10\log_{10}(R_b) = 9.6 + 10\log_{10}(4000) = 9.6 + 36.0 = 45.6~\text{dBHz} \end{align*}\]
Table 2. S-band TT&C Command Uplink Budget (2.1 GHz, LEO 600 km, 10\(^\circ\) elevation)
Parameter Value Units
Transmit Side (Ground Station)
Transmit power \(P_t\) \(+7.0\) dBW (\(= 5\) W)
Transmit antenna gain \(G_t\) \(+33.8\) dBi (3 m dish, 55% eff., \(f=2.1\) GHz)
Feed and cable losses \(L_{\text{tx}}\) \(-0.5\) dB
Pointing loss (worst-case) \(-0.5\) dB
EIRP \(\mathbf{+39.8}\) dBW
Propagation (Worst Case: 10\(^\circ\) elevation)
Slant range (10\(^\circ\) el., 600 km orbit) 1930 km
Free-space path loss FSPL \(-164.6\) dB
Atmospheric absorption \(-0.5\) dB (elevated \(L_{\text{gas}}\) at low elevation)
Ionospheric loss \(-0.2\) dB (S-band, typical)
Total path losses \(\mathbf{-165.3}\) dB
Receive Side (Spacecraft)
Receive antenna gain \(G_r\) \(0.0\) dBi (omnidirectional monopole)
System noise temperature \(T_{\text{sys}}\) 1000 K \(= +30.0\) dBK (Earth-viewing, body noise)
Spacecraft \(G/T\) \(-30.0\) dB/K (\(= 0.0 - 30.0\))
Boltzmann constant \(k_B\) \(+228.6\) dBW/K/Hz
Link Performance
Received \(C/N_0 = 39.8 - 165.3 + (-30.0) + 228.6\) \(\mathbf{+73.1}\) dBHz
Required \(C/N_0\) (BPSK, 4 kbps, BER \(10^{-5}\))
Required \(E_b/N_0\) (BPSK, BER \(10^{-5}\)) \(+9.6\) dB
Implementation loss \(+0.5\) dB
Data rate term \(10\log_{10}(4000)\) \(+36.0\) dBHz
Required \(C/N_0\) \(\mathbf{+46.1}\) dBHz
Link margin \(= 73.1 - 46.1\) \(\mathbf{+27.0}\) dB

Interpretation

The 27 dB margin at worst-case 10\(^\circ\) elevation is deliberately generous for a command uplink: TT&C reliability is safety-critical, and the 4 kbps command rate is intentionally conservative. The large margin enables robust command reception even under interference, ground-antenna mispointing or a spacecraft in a degraded attitude, and it would allow a much smaller ground antenna or lower transmit power. If the spacecraft’s attitude is uncertain (for example during an emergency safe mode), the omnidirectional receive antenna provides full-sphere coverage. At higher elevation angles (for example 45\(^\circ\), slant range about 815 km) the path loss falls by \(20\log_{10}(1930/815) \approx 7.5\) dB, increasing the margin accordingly.

Example 3: X-band LEO Data Downlink

Scenario Definition

Earth Observation (EO) satellites, particularly Synthetic Aperture Radar (SAR) missions, generate data at rates that challenge X-band downlink capacity. This example computes the link budget for an X-band data downlink from a LEO spacecraft to a mid-sized ground station. All inputs are assumed, illustrative values and not the parameters of a specific mission.

Scenario: 8.1 GHz X-band downlink in the Earth-exploration satellite allocation, 2 W (3 dBW) transmit power, a shaped-beam spacecraft antenna with 12 dBi gain, a 5 m ground receiving antenna, 600 km circular orbit, worst-case 10\(^\circ\) elevation angle, and a target of 150 Mbps.

At 8.1 GHz, \(\lambda = 3\times10^8 / 8.1\times10^9 = 0.037\) m. The slant range at 10\(^\circ\) elevation from a 600 km orbit is about 1930 km:

\[\begin{align*} \text{FSPL} &= 20\log_{10}\!\left(\frac{4\pi \times 1{,}930 \times 10^3}{0.037}\right) = 20\log_{10}(6.55 \times 10^{8}) = 176.3~\text{dB} \end{align*}\]

Ground receive antenna gain (5 m dish, 70% efficiency at 8.1 GHz):

\[\begin{align*} G_r &= 0.70 \times \left(\frac{\pi \times 5 \times 8.1 \times 10^9}{3 \times 10^8}\right)^2 = 0.70 \times 179{,}857 = 125{,}900 \Rightarrow 51.0~\text{dBi} \end{align*}\]
Table 3. X-band Data Downlink Budget (8.1 GHz, LEO 600 km, 10\(^\circ\) elevation)
Parameter Value Units
Transmit Side (Spacecraft)
Transmit power \(P_t\) \(+3.0\) dBW (\(= 2\) W)
Transmit antenna gain \(G_t\) \(+12.0\) dBi (shaped-beam horn, assumed)
Waveguide and switch losses \(L_{\text{tx}}\) \(-1.5\) dB
Pointing loss \(-0.5\) dB
EIRP \(\mathbf{+13.0}\) dBW
Propagation (10\(^\circ\) elevation, 1930 km slant)
Free-space path loss FSPL \(-176.3\) dB
Atmospheric absorption \(L_{\text{gas}}\) \(-0.5\) dB (X-band, low elevation)
Rain fade margin (0.1% time) \(-2.0\) dB (illustrative; X-band is less affected)
Total path losses \(\mathbf{-178.8}\) dB
Receive Side (Ground Station)
Receive antenna gain \(G_r\) \(+51.0\) dBi (5 m dish, 70% eff.)
Feed and LNA losses \(-0.5\) dB
System noise temperature \(T_{\text{sys}}\) 100 K \(= +20.0\) dBK
Ground station \(G/T\) \(+30.5\) dB/K (\(= 51.0 - 0.5 - 20.0\))
Boltzmann constant \(k_B\) \(+228.6\) dBW/K/Hz
Link Performance
Received \(C/N_0 = 13.0 - 178.8 + 30.5 + 228.6\) \(\mathbf{+93.3}\) dBHz
Required \(C/N_0\) for 150 Mbps, DVB-S2 8PSK 2/3
Target data rate \(R_b = 150\) Mbps \(10\log_{10}(150\times10^6) =\) \(+81.8\) dBHz
Required \(E_b/N_0\) (from \(E_s/N_0 = 6.62\) dB) \(+3.6\) dB
Implementation loss \(+1.0\) dB
Required \(C/N_0\) \(\mathbf{+86.4}\) dBHz
Link margin \(= 93.3 - 86.4\) \(\mathbf{+6.9}\) dB
Max rate at 0 dB margin (same MODCOD) \(\mathbf{\sim}\)730 Mbps (\(= 150 \times 10^{0.69}\))

Interpretation

The link closes with a 6.9 dB margin at the lowest elevation, so the radio link is not the binding constraint for this scenario. The practical limits are more likely to be the spacecraft data storage capacity, the contact duration (a few minutes to about ten minutes per pass for a 600 km orbit, depending on the minimum elevation used), and the bandwidth available in the Earth-exploration satellite allocation at X-band. With 8PSK 2/3 (2 bit/s per symbol before roll-off), 150 Mbps needs roughly 75 Msymbol/s, or about 90 MHz of bandwidth with a typical roll-off, which fits within the 8025–8400 MHz allocation. At higher elevations the margin grows, and the surplus can be used for a higher-order MODCOD, a higher data rate, or reduced transmit power.

Example 4: Optical Free-Space Link (LEO Downlink)

Scenario Definition

Optical free-space communication (FSO) links offer orders-of-magnitude higher bandwidth density than radio frequency links at comparable aperture sizes. This example computes the link budget for a 1550 nm downlink from a LEO spacecraft to an optical ground station, representative of LEO optical downlink demonstrations such as NASA’s TBIRD CubeSat mission. All inputs are assumed, illustrative values and not the parameters of a specific mission.

Scenario: Wavelength \(\lambda = 1550\) nm (\(1.55\times10^{-6}\) m), 1 W transmit laser power, 10 cm transmit telescope on the spacecraft, 0.5 m receive telescope at the ground station, 600 km altitude, 45\(^\circ\) elevation angle (slant range \(\approx\)815 km), direct-detection receiver, target data rate 10 Gbps.

Optical Link Budget Calculation

For a diffraction-limited beam from a 10 cm transmit aperture, the divergence (full angle to the first null) is:

\[\begin{align*} \theta_{\text{div}} &= \frac{2.44\,\lambda}{D_t} = \frac{2.44 \times 1.55 \times 10^{-6}}{0.10} \approx 38~\mu\text{rad} \end{align*}\]

which produces a beam diameter of about 31 m at 815 km. The transmit telescope gain (analogous to antenna gain) with aperture efficiency \(\eta_t = 0.8\) is:

\[\begin{align*} G_t &= \eta_t \left(\frac{\pi D_t}{\lambda}\right)^2 = 0.8 \times \left(\frac{\pi \times 0.10}{1.55 \times 10^{-6}}\right)^2 = 0.8 \times (2.03 \times 10^5)^2 = 3.3\times10^{10} \Rightarrow 105.2~\text{dBi} \end{align*}\]

The free-space path loss at \(\lambda = 1550\) nm over 815 km is:

\[\begin{align*} \text{FSPL}_{\text{opt}} &= 20\log_{10}\!\left(\frac{4\pi \times 815 \times 10^3}{1.55 \times 10^{-6}}\right) = 20\log_{10}(6.61 \times 10^{12}) = 256.4~\text{dB} \end{align*}\]

The receive telescope gain with \(\eta_r = 0.7\) and \(D_r = 0.5\) m is:

\[\begin{align*} G_r &= \eta_r \left(\frac{\pi D_r}{\lambda}\right)^2 = 0.7 \times \left(\frac{\pi \times 0.5}{1.55 \times 10^{-6}}\right)^2 = 0.7 \times 1.03 \times 10^{12} \Rightarrow 118.6~\text{dBi} \end{align*}\]

As a cross-check, the geometric spreading loss is approximately \((D_r/(\theta_{\text{div}}\,d))^2 = (0.5/31)^2 \Rightarrow -35.8\) dB, compared with \(-32.6\) dB from \(G_t - \text{FSPL} + G_r\); the difference reflects the top-hat versus Gaussian beam assumption.

For the receiver, an assumed requirement of about 1000 photons per bit (a value representative of a direct-detection receiver; the photon energy at 1550 nm is \(1.28\times10^{-19}\) J) at 10 Gbps gives a minimum received power of

\[\begin{align*} P_{\text{req}} &= 1000 \times 1.28\times10^{-19}~\text{J} \times 10^{10}~\text{bit/s} = 1.28~\mu\text{W} \approx -29~\text{dBm} = -59~\text{dBW} \end{align*}\]
Table 4. Optical Free-Space Link Budget (1550 nm, LEO 600 km, 45\(^\circ\) elevation)
Parameter Value Units
Transmit Side (Spacecraft)
Transmit laser power \(P_t\) \(0.0\) dBW (\(= 1\) W)
Transmit telescope gain \(G_t\) \(+105.2\) dBi (10 cm aperture, \(\lambda=1550\) nm)
Optical TX losses (WDM, isolator) \(-2.0\) dB
Pointing loss (fine APT residual) \(-1.5\) dB
EIRP (optical) \(\mathbf{+101.7}\) dBW
Propagation (815 km slant range, 45\(^\circ\) el.)
Free-space path loss FSPL \(-256.4\) dB (\(f = c/\lambda = 193\) THz)
Atmospheric turbulence (scintillation) \(-3.0\) dB (assumed)
Cirrus cloud / thin cloud \(-2.0\) dB (marginal conditions)
Aerosol extinction \(-0.5\) dB (assumed)
Total path losses \(\mathbf{-261.9}\) dB
Receive Side (Ground Telescope)
Receive telescope gain \(G_r\) \(+118.6\) dBi (0.5 m aperture, \(\eta_r = 0.70\))
Optical RX losses (bandpass filter, fibre) \(-3.0\) dB
Effective receive system gain \(+115.6\) dBi
Link Performance
Received power \(= 101.7 - 261.9 + 115.6\) \(\mathbf{-44.6}\) dBW
Required Received Power at 10 Gbps
Assumed receiver requirement (about 1000 photons/bit) \(-59.0\) dBW (\(\approx -29\) dBm)
Link margin \(= -44.6 - (-59.0)\) \(\mathbf{+14.4}\) dB
Notes
Margin without cirrus and scintillation losses: \(14.4 + 2.0 + 3.0 = +19.4\) dB
Adaptive optics can recover part of the turbulence loss in good seeing
Photon-counting (SNSPD) detectors can operate at far fewer photons per bit than assumed here

Interpretation

The 14.4 dB margin for a 10 Gbps optical link from 600 km is healthy in clear conditions but depends strongly on the assumed receiver requirement, on atmospheric turbulence and on pointing. Atmospheric turbulence and cloud blockage impose deep fades that require one or more of: (1) optical ground station networks (diversity between multiple stations reduces the probability of cloud blockage; turbulence is site-specific); (2) adaptive optics at the ground telescope to compensate the wavefront distortion induced by the atmosphere; or (3) more sensitive detectors such as superconducting nanowire single-photon detectors (SNSPDs), which operate at far fewer photons per bit than conventional receivers but require cryogenic cooling.

NASA’s DSOC technology demonstration on the Psyche spacecraft (Section 31.4) uses a superconducting nanowire detector at Palomar for this reason: the sensitivity improvement allows photon-counting communication from tens to hundreds of millions of kilometres with a 22 cm flight transceiver aperture. For LEO commercial applications, the trade between link budget, ground-station network coverage, and APT (Acquisition, Pointing, and Tracking) complexity will determine the practical data rates achievable with 5–15 cm spacecraft apertures.

Link Budget Summary Formulae

Key Equations

The following equations encapsulate the complete link budget calculation chain. All quantities are in SI units unless subscript dB, dBW, dBi, dBK, or dBHz is specified.

Complete Link Budget Formula Set

Free-space path loss:

\[\begin{align*} \text{FSPL}_{\text{dB}} &= 20\log_{10}\!\left(\frac{4\pi d}{\lambda}\right) = 20\log_{10}(d) + 20\log_{10}(f) - 147.55 \end{align*}\]

where \(d\) is in metres, \(f\) in Hz, and the constant \(-147.55 = 20\log_{10}(4\pi/c)\).

Effective Isotropic Radiated Power:

\[\begin{align*} \text{EIRP}_{\text{dBW}} &= P_{t,\text{dBW}} + G_{t,\text{dBi}} - L_{tx,\text{dB}} \end{align*}\]

Carrier-to-noise density ratio:

\[\begin{align*} \left(\frac{C}{N_0}\right)_{\text{dBHz}} &= \text{EIRP}_{\text{dBW}} - \text{FSPL}_{\text{dB}} - L_{\text{atm,dB}} - L_{\text{misc,dB}} + \left(\frac{G}{T}\right)_{\text{dB/K}} + 228.6 \end{align*}\]

Energy-per-bit to noise density:

\[\begin{align*} \left(\frac{E_b}{N_0}\right)_{\text{dB}} &= \left(\frac{C}{N_0}\right)_{\text{dBHz}} - 10\log_{10}(R_b) \end{align*}\]

Shannon channel capacity:

\[\begin{align*} C &= B\log_2\!\left(1 + \frac{C/N_0}{B}\right)~\text{bit/s} \end{align*}\]

Antenna gain from aperture:

\[\begin{align*} G_{\text{dBi}} &= 10\log_{10}\!\left[\eta\left(\frac{\pi D f}{c}\right)^2\right] \end{align*}\]

System noise temperature:

\[\begin{align*} T_{\text{sys}} &= T_{\text{ant}} + T_{\text{feed}} + T_{\text{LNA}} + \frac{T_{\text{post-LNA}}}{G_{\text{LNA}}}~[\text{K}] \end{align*}\]

Noise Figure to Noise Temperature Conversion

The noise figure \(F\) (linear, dimensionless) of a device at physical temperature \(T_0 = 290\) K is related to the equivalent noise temperature \(T_e\) by:

\[\begin{align*} T_e &= T_0(F - 1) = 290(F - 1)~\text{K} \end{align*}\]

Common conversions at \(T_0 = 290\) K:

Table 5. Noise Figure to Equivalent Noise Temperature Conversion
Noise Figure (dB) Linear \(F\) Noise Temperature (K)
0.3 1.072 20.8
0.5 1.122 35.4
1.0 1.259 75.1
1.5 1.413 119.9
2.0 1.585 169.8
3.0 1.995 288.7
5.0 3.162 627.0
10.0 10.0 2610.0

Modulation and Coding Requirements

Table 6 provides required \(E_b/N_0\) values for common DVB-S2 modulations and coding rates (normal frame, AWGN, quasi-error-free operation). The values are derived from the \(E_s/N_0\) thresholds of ETSI EN 302 307 using \(E_b/N_0 = E_s/N_0 - 10\log_{10}(\eta)\), where \(\eta\) is the number of information bits per symbol; they are ideal thresholds, so an implementation loss (typically 0.5–1.5 dB) must be added.

Table 6. Required \(E_b/N_0\) for Common DVB-S2 MODCODs (ideal quasi-error-free thresholds, no implementation loss)
Standard Modulation Code Rate Spectral Eff. Req. \(E_b/N_0\) (dB)
DVB-S2 QPSK 1/2 1.0 b/s/Hz 1.0
DVB-S2 QPSK 3/4 1.5 b/s/Hz 2.3
DVB-S2 QPSK 9/10 1.8 b/s/Hz 3.9
DVB-S2 8PSK 2/3 2.0 b/s/Hz 3.6
DVB-S2 8PSK 3/4 2.25 b/s/Hz 4.4
DVB-S2 16APSK 2/3 2.67 b/s/Hz 4.7
DVB-S2 16APSK 3/4 3.0 b/s/Hz 5.4
DVB-S2 32APSK 3/4 3.75 b/s/Hz 7.0
Uncoded BPSK — 1.0 b/s/Hz 9.6 (BER \(10^{-5}\))

Rain Fade Statistics

Rain attenuation at Ka-band (20 GHz) is the dominant variable impairment in GEO downlinks at mid-to-tropical latitudes. The ITU-R P.618 model calculates the attenuation exceeded for \(p\)% of the average year from the local rain rate exceeded for 0.01% of the time (ITU-R P.837), the path geometry and the frequency. Typical results at 20 GHz and 45\(^\circ\) elevation for 0.01% of the time are roughly 3–7 dB in temperate northern and central Europe and of the order of 15–25 dB or more in heavy-rain tropical regions; Table 7 gives indicative orders of magnitude only, and site-specific values must be computed with ITU-R P.618 using local data.

Table 7. Indicative Ka-band Rain Attenuation Orders of Magnitude (20 GHz, 45\(^\circ\) elevation); compute site-specific values with ITU-R P.618
Climate 0.1% of time 0.01% of time
Temperate (northern/central Europe) about 1–3 dB about 3–7 dB
Mediterranean / subtropical about 3–6 dB about 8–15 dB
Tropical (heavy rain) about 8–15 dB about 15–30 dB

Satellite Link Budget Design Rules of Thumb

  • For GEO Ka-band: without ACM, the clear-sky margin must cover the rain fade for the required availability (often several dB in temperate climates and more than 10 dB in the tropics).

  • For LEO S/X-band TT&C: command links are normally designed with generous margin (well above the typical 3–6 dB minimum) at worst-case elevation, because reliable command is safety-critical.

  • For optical links: diversity among 3 ground stations at \(>\)500 km separation reduces cloud outage probability below 1%.

  • In the power-limited regime, every 3 dB increase in EIRP or \(G/T\) doubles the achievable data rate at the same \(E_b/N_0\).

  • Rule of thumb FSPL: \(\text{FSPL}_{\text{dB}} \approx 92.4 + 20\log_{10}(f_{\text{GHz}}) + 20\log_{10}(d_{\text{km}})\) (exact for SI: constant \(= 92.44\)).

  • System noise temperature: a 1 dB LNA noise figure adds only 75 K; a 0.3 dB LNA adds only 21 K. LNA quality matters.

Complete Link Budget Template

Table 8 provides a generic blank link budget template suitable for hand calculation or spreadsheet implementation. Positive entries contribute to received \(C/N_0\); negative entries are losses.

Table 8. Generic Link Budget Template
Parameter Value Units
Transmit Side
Transmit power \(P_t\) dBW
Transmit antenna gain \(G_t\) dBi
Transmit line/feed losses \(L_{\text{tx}}\) dB
Pointing loss dB
EIRP dBW
Propagation
Frequency \(f\) GHz
Slant range \(d\) km
Wavelength \(\lambda = c/f\) m
FSPL \(= 92.44 + 20\log f_{\text{GHz}} + 20\log d_{\text{km}}\) dB
Atmospheric absorption \(L_{\text{gas}}\) dB
Rain fade margin (99.X% avail.) dB
Miscellaneous losses \(L_{\text{misc}}\) dB
Total losses dB
Receive Side
Receive antenna gain \(G_r\) dBi
Receive line/feed losses \(L_{\text{rx}}\) dB
System noise temperature \(T_{\text{sys}}\) K / dBK
Figure of merit \(G/T = G_r - L_{\text{rx}} - T_{\text{sys,dBK}}\) dB/K
Boltzmann constant \(k_B\) \(+228.6\) dBW/K/Hz
Received \(C/N_0\) = EIRP \(-\) Losses \(+ G/T + 228.6\) dBHz
Performance Assessment
Data rate \(R_b\) bps
\(10\log_{10}(R_b)\) dBHz
Required \(E_b/N_0\) (from MODCOD table) dB
Implementation loss dB
Required \(C/N_0 = E_b/N_0 + 10\log R_b +\) impl. loss dBHz
Link margin = Received \(C/N_0 -\) Required \(C/N_0\) dB

Comparison of Worked Examples

Table 9 summarises all four worked examples for rapid comparison. The margins in these examples depend entirely on the assumed inputs and should not be read as typical values. In general, radio links are bandwidth-constrained and are often operated close to their limits with adaptive coding and modulation, whereas optical links are limited by atmospheric effects, pointing and detector sensitivity but can support very high data rates.

Table 9. Summary of Worked Link Budget Examples
Example Band Link Type \(C/N_0\) (dBHz) Required Margin (dB)
Ex. 1: Ka GEO DL 20 GHz GEO \(\to\) VSAT 74.7 72.3 +2.4
Ex. 2: S-band UL 2.1 GHz GND \(\to\) LEO TT&C 73.1 46.1 +27.0
Ex. 3: X-band DL 8.1 GHz LEO EO \(\to\) GND 93.3 86.4 +6.9
Ex. 4: Optical DL 193 THz LEO OPT \(\to\) OGS \(-44.6\) dBW \(-59.0\) dBW +14.4